P1314 Engine Trouble Code

When you check engine light came on code P1314 the reason should be Engine Light ON (or Service Engine Soon Warning Light). However your vehicle's manufacturer may have a different definition for the P1314 OBD-II Diagnostic Powertrain (P) Trouble Code. So you should chech it on our car models.

When your car's 'P1314 Check Engine' light comes on, it's usually accompanied by a sinking feeling in the pit of your stomach. The light could mean a costly problem, like a bad catalytic converter, or it could be something minor, like a loose gas cap. But in many cases, it means at minimum that you'll be visiting the car dealer to locate the malfunction and get the engine conducted light turned off.

P1314 Code Meaning :

The oxygen (02) sensors on your car measure the oxygen in the exhaust to determine how rich or lean the ratio of fuel and air are in the cylinders. Optimizing this mixture means better fuel economy and fewer exhaust emissions.

P1314 OBD-II Diagnostic Powertrain (P) Trouble Code Description

P1314 OBD-II Trouble Code Misfire Rate Catalyst Damage Fault Bank 2 is one of the definitions for the P1314; however your vehicles manufacturer may have a different definition for the P1314 code. Please check below for your sp P1314 code. Fuel Rail Pressure Sensor Circuit Malfunction and Ignition/Distributor Engine Speed Input Circuit Malfunction causes most of code P1314.

Reason For P1314 Code

The reason of P1314 OBD-II Engine Trouble Code is Fuel Rail Pressure Sensor Circuit Malfunction.

P1314 code on vehicles with electronically controlled automatic transmissions, the 3-4 shift solenoid is responsible for actuating the hydraulic circuits to activate clutches or bands that change gears inside the automatic transmission in your car.

How To Repair P1314 Code

Before starting let's see P1314 repairing process steps:

• Qualified technicians will begin by using a scan tool to access P1314 code stored in the ECU.
• Technicians will note P1314 code present and any freeze frame data associated with them.
• After all, if you sure the engine trouble is finished, the code will be cleared.

The fluid pressure sensor provides the PCM with the data necessary to monitor the transmission performance. If the fluid pressure increases, the electrical voltage reading from the pressure sensor will increase; if the pressure decreases, the voltage decreases.

This process helps the mechanic narrow down the exact cause of the issue. If the transmission fluid fix did not cause the code to disappear from the PCM, then next step is to inspect the electrical components, and to continue working through possible repairs until the correct issue is found.

Sometimes P1314 code comes with P131400 code.

Diagnosis Of Engine Error OBD Code P1314

It's essential to diagnose this trouble code. Then are some way which a handyperson should follow for diagnosing the problem that started a P1314 trouble code to be stored

The first step is introductory and is about reacquiring all the canons that have been set. For this, the individual scanner will have to be plugged into the individual harborage of your vehicle. Make sure you indurate frame the data. Any canons that were set previous to the P1314 code will have to be sorted first, as they may have been the reason for the law to set in the first place. It's always good to rule that out.

The coming step is to run a introductory examination of all the electrical circuits, connectors, wiring etc for damages similar as becks, erosion, fraudulent legs etc. All of these will have to be repaired or replaced. After that's sorted, clear the canons and go on a test drive to see if it resets. In case it resets, you'll have to continue your opinion. Depending on your vehicle you may have a vacuum operated selector or a vacuum solenoid if it's electrically actuated. In the case of the former, a hand held vacuum pump will have to be used to testit.The purpose is to see if the internal stopcock is getting turned by the selector, motor or solenoid. In order to do this, a command can be transferred to the system with scanner or by driving the vehicle under the special conditions that will spark the system. While this is passing keep an eye on the checkup tool data for the result.